UberSeal Anti-Lime Sealer | Waterproofing | Resincoat
   

UberSeal Anti-Lime Sealer Concentrate

TNK011

UberSeal Anti-Lime Sealer Concentrate is applied to concrete, curing to form a water-repellent surface that resists lime efflorescence.

 

  • Prevents blockages in cavity drain membranes
  • Suitable for both old and new concrete
  • Does not block pores in substrate, keeping the concrete breathable
  • Highly concentrated, easy transport, reduced plastic packaging

  

Hurry! only 500 items left in stock.
£35.64
£39.60
Save 10%
Tax included
Quantity

Add to Wishlist

Anti-Lime Sealer Concentrate

UberSeal Anti-Lime Sealer Concentrate is specifically formulated to prevent free lime leaching in new concrete. It is commonly used alongside the UberSeal range of waterproofing membranes and drainage system components for effective anti-lime treatment in new concrete.

This inhibitor is also suitable for treating walls and existing concrete slabs, especially in cut recesses prepared for drainage channel installation.

When diluted, the treatment penetrates the surface of masonry or concrete, reducing capillary pore size. These narrower pores significantly decrease the movement of free lime through the surface.

 

COVERAGE RATES

Once diluted, a 20 Litre mixed unit should have a coverage of up to 200m².

 

APPLICATION GUIDE

Preparation

Remove all loose material and surface laitance, such as dust, oil, grease, corrosion, and organic growth, using appropriate methods like wet grit or water blasting techniques.

Ensure there is no water pooling before application. UberSeal Anti-Lime Sealer can be applied to matt damp surfaces, but not wet surfaces.

 

Application

  1. Add 16 litres of clean water into a clean container or sprayer. Pour the contents of the Anti-Lime Sealer into the container or sprayer.
  2. Fill the Anti-Lime Sealer packaging with an additional 2 litres of water and pour it into the container or sprayer.
  3. Apply evenly to the clean substrate using a coarse sprayer, masonry roller, or brush at a rate of 0.2–0.3 l/m² in a single coat.
  4. Allow the substrate to absorb the Anti-Lime Sealer for a minimum of 3 hours. Once touch dry, it can be walked on or covered.

 

IMPORTANT INFORMATION

Do not apply the lime inhibitor in the following situations:

  • on frost filled surfaces or when the temperature is 5°C and falling
  • when the temperature is 25°C and rising
  • Do not apply more than one coat.
  • Do not re-apply once dry.
  • Protect non-target surfaces from the inhibitor due to staining - it will be extremely difficult to remove once dry.
  • Clean equipment immediately after use with water.
: TNK011
: 500 Items
Hurry! only 500 items left in stock.

Specific References

EAN13
5056771735158

Use collapsible tabs for more detailed information that will help customers make a purchasing decision.

Ex: Shipping and return policies, size guides, and other common questions.

  • Paste the label on a flat surface on the package
  • Make sure that both 1D and 2D barcodes are clearly visible
  • Ensure that the label is smooth and isn’t creased or wrinkled
  • Check for any tears, dents, holes or scratches
  • Pack your product tightly, with the right size packaging
  • Ensure both barcodes are on a flat surface of the package
SizeSMLXL
Men 7-10 10-13 13-15 15-17
Women 7-9 10-12 13-14 15-16

Example Shown : SIZE XL, Hem to Hem 84cm OR 33 ,SIZE L, Hem to Hem 84cm OR 33 ,SIZE M, Hem to Hem 84cm OR 33 ,SIZE S, Hem to Hem 84cm OR 33
Product added to compare.